Saturday, February 12, 2011

Best Place To Buy Ice Skate In Toronto

Ford RS 200 MSC Introduction and basic preparation

is the first complete scale model 1 / 32 of this manufacturer which, from the beginning, is committed to quality and ingenuity to become a very important gap in the Slot .

Your Home (titanium frame) accessories and Slot material on the two scales 1 / 32 and 1 / 24 and later with multi chassis adaptable " Monte Carlo" and its subsequent evolution have given as a result the base adaptable to all types of battle axes as driver for both total length of the body. Fair
In the 2011 Nuremberg MSC submitted a chassis base "Montecarlo " suspension be adjustable by sliding the base of the new Porsche 959 of Raid. Let
, if you will, to break down this new model has come to our particular garage.
The size seems a little out of scale may be nearer the 1 / 30 than the usual 1 / 32 but is well proportioned.


SHEET of Ford RS 200:
total body length: 1,251 mm.
maximum body width (middle): 59 mm.
front wheel arch width: 58 mm.
rear wheel arch width: 57 mm.
full weight the three screws on the bodywork: 20.2 g . Maximum distance phone
/ rear axle: 99 mm Depth
guide: 7 mm Total weight
full chassis number: 64.9 g . Total weight
series car without magnet: 85.1 g .
original rim diameter: 16.80 mm Overall Diameter
original wheel: 20 mm
front and rear pulley diameter: 14.03 mm Shaft
calibrated diameter of 2.38 mm / 50 mm. length.
Engine: MSC Thunder 2 / 21 000 rpm at 12 v / 320 gr . x cm. ma consumption 190.
direct magnetic attraction engined - 7.40 ums ( Kelving Light )
magnetic attraction as the original tires on the track: - 5.5 ums
Pinion: 5.5 mm diameter and 10 teeth.
Crown: 14.70 mm diameter 27 teeth white.
Static Analysis:
The thickness of the plastic body is very thin (1 mm poor) depending on the area .....

.... which together with a plate of lexan material which supports two plastic dolls representing the figures of pilot and copilot ...

..... next to the extinguisher made from plastic material as the board representing instruments, steering wheel and own hands, roll bars security result aesthetically a very consistent for a very content.

gravure grids everywhere .... front ....

..... MSC should improve the reproduction of the front light .....

.... and photogravures ago, the quality of the grids in contrast to the low quality of optical rear external paint and lack of relief ....

..... on the roof admission nozzles etched grid .... nozzles different between the two models available and profiled, with a sticker on it forming the red on white lists ....

Comment great detail to accompany this model the decals needed to complete the vehicle's original decor reproduced maintaining the legal commitment of advertising anti snuff. All of a detail for older children as we we want the most accurate replicas of reality.

Through the transparency of the "crystals" can be seen in a very basic and simulated motor paperback (base VACUFORM ) and more when compared to the reference model of origin inevitable Exin and pending playing Scalextric this year.

Reproduction of the antenna is flexible and almost unbreakable ...

..... the opposite of mirrors mirrors are robust although rigid material.
The exhaust pipe is loose in my unit ......

.... some glue and countersinking the end of it with a bit is very realistic.


Is not you think?. They are also very realistic
skirts elastic behind the rear wheel arches located in the body ....

.... as located on the chassis front.

mechanics:
The chassis is composed of the basis of " Monte Carlo" with lateral appendages ....

..... to "close" a little more and is more attractive set as chassis adapted to the body. power cables are distinctive because they are flexible but can be desired shape and therefore we have passed under the front axle so you do not chafe at any point. Thus the focus of the guide is perfect.

The weight of the entire mechanical assembly is 64.90 gr .
The wheels are plastic and have a well balanced, with a diameter of 16.80 mm and weighs 1.3 grams . each.


Aesthetically are more than good although we would have liked a little more depth in the central fringe to differentiate the front tire on the rear.
this topic and we'll fix it later as the hub cap tire easily disassembled
total diameter series tire is 20 mm

The quality of the tires is limited to be in the box or cabinet speaker after several rounds our section improves grip somewhat but is not competitive.
The quality of the pad "Pirelli " in the rubber is of very good quality.
The two pulleys on the right side of the chassis (top view) are covered by plastic teeth metric allen 2 mm with an outer diameter of 14.03 mm and a weight of 0.4 gr .

The engine is el nuevo Thunder 2 con 21.000 r.p.m. a 12 v. con un par de 230 gr . por cm. y un consumo de 190 m.a. ; la atracción magnética directa es de 7,4 u.m.s. Kelving Light ....

.... y el campo magnético del motor a 2 m.m del suelo (grosor de los neumáticos originales hace un diámetro de rueda 20 m.m) se quede en 5,5 u.m.s.

Hay que hacer notar que el motor queda por debajo del chasis 1 m.m pero el diámetro total de la rueda es excesivo y para la preparación básica lo vamos a sustituir los 4 neumáticos.

La transmisión está encargada a un Scaleauto home pinion of 10 teeth that transmits engine power to a white crown multiperforated aluminum base Scaleauto source of 27 teeth + centering module manufactured in brass pinion .....

independent .... the crown to set all kinds of sprocket diameter.
original transmission has a ratio of 2.7 and it seems a bit long, because for Slot Rally is more suitable ratio 3.3.

this chassis bearings are spherical self centering it as you have seen other manufacturers as it Slot and Tecnitoys . (Better, at present, impossible)

while stressing the firm hold the engine to the frame with single screw.
The pivoting guide is also home Scaleauto with an already seen MB guides, has a depth of 7 mm with a dock much like Ninco .....

.... we review sanding the front as it can be seen in the picture below because it conflicts with the lower tracks SCX.

Braids are very soft and very good quality.

The connection between the body and chassis is made by three aluminum screws we have sanded the "neck" .....

... to promote body tilt.
To dampen the noise vibration parasites own car handle three silicone pads (red) located on the chassis. (All details of design)

The first thing to do is check the entire assembly to check the fit around the chassis and its components, once everything in its right place the height of front axle by the stud over the phone to deepen pivoting properly in the lane.
Note: the chassis is ready for asparagus less, but my unit does not have them.

Once at this point going to solve the ugly of the hubcaps. 1 º dismantle
doing something slightly curved lever and fine ....

... dismantle the hub cap and reproduction of the brake disc attached to it ...

.... Notice the difference between the disc from the right and the rest, we must take into account when reassembled so that the clamp is properly viewed from the outside located. Then we go to the bottom of fringe playing disc brakes to give more depth ....

.... once placed at our leisure, we place a drop of cyano on a disposable basis

... and the tip of a toothpick or similar paste with a minimal amount of cyanoacrylate to secure the disks to the fringe ........

.... while we must make room in the back of the rim with a hole of 6 mm in diameter and carefully go slow "eating" material as we see in the picture below ....

......... about 2 mm, having that the axes are 50 mm allows us greater depth on the rear axle .....

..... and the end result worth it if we keep the original wheels.

We will remove the optical ....

.... and funds with orange paint clear signal and background chrome headlight front body accessories ....

... such as transparencies and reproduction of the taillights.

While the paint is dry place the decals as we have searched online in the images of the actual vehicle as in the decals on the reference is not the correct location of the same. We assemble and paste
white glue all the pieces painted and after eating at a stretch prove that such is the beauty.

Dynamic test:
Change the 4 original tires for a Spirit narrow front and wider the tire protruding over the rear wheel arches of the body, the diameter of the wheels we have in 18.33 mm instead of 20 mm of the original tires.

The height of the template engine has been measured at 1.5 mm, remember that the motor is 1 mm below the plane of the chassis.
Under these conditions the real magnetic attraction of the rail motor is 6.8 ums
Once all set, weighted body to 25 gr. as indicated by the rules, adjusted and oiled mechanics we go to the section prepared for this occasion. Avant
regulated control my taste 6-2-5-1 - traction control 9 / 1, 7 and 12 curb v. First
try one of the best cars Classic Rally Slot Racing Fly BMW M1 .....

.... Skorpion engine and rear tire width Spirit for reference performance, What a wonderful car! ..... having made the fastest time reference, try RS 200 to begin the comparison. RS200
The behavior is very noble, like the safe and free from noise M1 and roll on the track with outstanding finesse, but tends to lose its way back behind a little rough, but without losing the rail line, times M1, although close, do not go.
To remedy the abruptness of the front axle skid regulate the bottom with a rod with 3 mm length and non-existent Spirit comes into our newly acquired unit.

As we do in 1 / 32 let the front just enough support on the measuring template and return to the section ............. the subject does not improve and stay in the days before, back back, remove the lower front studs and start to tighten the top two to be the front end that supports the phone barely more than 1 mm as it mentadidad of 1 / 24 and the nobility of the case "Montecarlo" We believe that permitting , setting the contrary to the usual 1 / 32 scale clean asphalt.
The chassis is completely parallel to the reference template.


The car is as safe as giving a lot, but a lot of confidence, the front axle and rear strip is no longer sharp curve at the exit, even though this engine has a very bad grape MSC Ford RS200 has more traction between curve and curve slightly down own times, the car is always masterfully guided by the guide and front axle with no right whatsoever on any type of curves, driving a delight but I still get to the time achieved by the unbeatable M1 de Fly Racing, but we are very close. Change
curve parameters electronic control for smoother power delivery of the engine without a fulfillment of what has been achieved, all the work he does driving the chassis, which is very noble, but radically control parameters are erratic and times are still very similar to those above but without the time of the M1 for a few tenths per lap.
Think about this and if we have address successful.

The torque motor Thunder2 reminds me of "Sogno" of MB but the engine braking MSC has increased despite having a transmission of 10/27 and after this discussion, the next line of evidence, the focus down gradually the voltage from 12 volts to 9 volts.
trial and error, I moved to 10.5 volts. With this voltage tracing the peak of M1. ETA
NOW! achieved the goal of a new car even with a "coconut" Slot Rally in the category of classics.

Y .......... If we compare the RS200 with a Peugeot 207, also Avant engine online? We are aware
we are comparing different categories "N" to "Classic", but so far I have not seen any linear Avant Slot Rally and do not think it by regulation.
Personally I could not take advantage of this car with the configuration Avant online because it is only sensitive in the interior cornering and downhill forks, it likes to do too much kibble without notice.
I think the chassis is very sensitive Avant weight from the center of gravity in the configuration with the engine online. In anglewinder is another story.
time achieved by our Peugeot 207 is slightly lower than the two classics. As it stands
tranche can be drawn the best conclusions because after several hours of shooting different vehicles on the section is very clean and is not referring to the reality of how we're going to find yourself in the sections in a test of Rally Slot.
After a few days without rolling down the track, tried to reverse to see how it behaves the RS200 over a non-roll or as clean as last week.
The RS200 is exemplary behavior by giving a huge security and forgiving all possible errors with a continuous rolling and great traction (4x4) between the lines to link with all kinds of curves.
got time for 10 laps is not bad but is lower than in the past few days.

tested now as it is the stretch of the M1 after shooting 10 rounds with Ford, the M1 is very noble but drift over the account and through 5 does not pull back enough grip to catch the time achieved by a Ford RS200 4x4 is superior in this case.

Conclusion:
We have another serious contender in the appropriate category (Group L) of the four possible categories according to unified rules Auto Slot Mediterranean and in the case of not having considered this category of classics at your Club, come into the category of Group "N" with the corresponding changes in the minimum weight of body (25 gr.) ballast pilots under the tray and replace the pinion 10 by a transmission 9 / 27 that even improves the performance of this great first car that offers full-scale MSC 1 / 32.
For better performance in the race we must change the original calibrated steel shafts quite soft with others of higher quality and if we screw the wheels, tires are 16.5 mm in the market for good quality, although a very modern classic wheels loses some essence of classicism.


We have already asked the Austin Metro to welcome him to our basement garage. From these lines
thank the invaluable assistance of our Charge Tati shop,

... and the editor Lucas ...

.... always accompanied by fellow Keta .....

..... without them this was not possible to test almost a month in duration. Salut Jordi
.

0 comments:

Post a Comment