Monday, November 29, 2010

Centerpieces Branches

Sloter. Presentation and basic preparation




supercars.net Image from

Without any intention to reflect on the disappearance of a manufacturer of slot as Sloter I present the version of the Lola T280 / 290, this English manufacturer.

Interestingly
Looking at the most superficial part of a model without going into excess amount of differences that the manufacturer has provisions to provide meticulous quality in the reproduction of this Lola T280/290.
say that this model reproduces Sloter dates from 1972 and ends his official competition period in 1983 ......... circuits

photos24hlemans.free.fr Image from
9 years of competition since the first version HU01 chassis developed by the Swedish driver Jo Bonier to participate in the Constructor's World Championship in the category of group 6 in 1972 with Gerard Larrousse and a lot of pilots from several countries relying on the English Jorge de Bagration to Le Mans in 1972 that only participated in training.

www.sportscardigest.com Image from

The Lola T280 engine powered by a 3-liter, 32-valve V-8 cylinder Ford Cosworth DFV source used in F1, developed by Patrick Head and John Barnard.
then Scuderia Filipinetti, occasionally used a 6-cylinder engine of the Ford Capri 3-liter engine and finally the various T290 versions of this car was powered by a 4-cylinder Ford Vega origin.

image taken from http://www.planetlemans.com/2008/07/20/le-mans-classic-grid-6

All real vehicle information can be found in this link: http://www.oldracingcars.com/lola/t280/


I comment all these details because Sloter has been taken into account in its various versions.
8 cylinder engine and roll bar than the 4 cylinder ........

front Three different depending on version ...........

................. and the dual exhaust for V-8 engine and simple 4-cylinder engine, with or without other rear-wheel rear panels ............

wheels are unique to every version when in fact it was not so but we must recognize that they are beautifully crafted .............. Closing moths are on another scale.

Sloter
This model is sold without a magnet, but for lovers can be adapted magnetic circular one so common in other manufacturers.
quality tire grip is very good .......

The pad seems quality .........

............ and plausible that it is identical to the model reproduced ..............

............. even when a tobacco company sponsoring it, covering it with stickers advertising as indicated by the European organization for child advocacy, adhesives certainly very easy to remove without damaging the pad as in other manufacturers ........ ...


.......... and enjoy the play as it is in reality.


All is not quite perfect in this model also has some shortcomings; perfection does not exist, and the eternal search for perfection is temporary ..... what today is very good, time to relegate it handles usually .......
Despite the good quality tire grip Ridge excess cylindrical shape and diameter of the rubber does not correspond to reality ...........

The different parts of the back are not well matched to the rest of the body (rear skirts) ..........

........... Reproduction of translucent headlights are unreal ..................


........... and taillights are intensity needed ............

......... side vent outlets are closed on the body ......


.......... when the case is scheduled to fund part of the open hole of the body ....

............ a little black paint on the body conceal this detail ....

Like any basic training, we start with the components of the box itself and improve the desire for improvement without any competition out of our home track.
We go to the basement workshop ....


transverse engine configuration with little effect or lack magnet and it does, I assure you, the car is on rails.

Throughout preparation is very important guide for the guide cables work well in their return and guided the vehicle .......


Observe the front of the open chassis .....

...... to facilitate handling and removal of the guide. Phone support is very robust.

The profile of the front tire is good for the passage of wheels, but very high in correspondence to the guide, in this context, because the stem guide so we can cut a piece of dry aquarium aerator tube to supplement this measure .......

.... and adapt it to the guide to the extent that work freely and return to their medium ......

...... with the front tires just lightly touch the template.


Some models necessary to sand the top burr front axle support to tilt about 2 m / m. cylindrical sanding with an emery top stop ..........

............. no we spend but the wheels touch the bottom step of the body.
We must thus be adjusted:

......... we see, again, that remains tight front axle ......

.......... regarding guidance on staff flat with 2 m / m. slack to absorb the irregularities of the track.


Once we fixed the front to rear:
We note that the original bearings are slack in the chassis brackets .......


We offer you an easy solution is not to close the media but to fill the gap with Teflon tape free plumbing. Let
comment how:
Cut two strips of Teflon of about 2.5 cm. long or less as the gap to be filled ....

............ rolled in each bearing no more than two laps as it doubles the tape increases the thickness of it and not need much thickness. Beware of excessive thickness as we can "force" without the accommodation of the two bearings! It is fair to attach the pad and not move or turn in their support.

We put the bearings in place and properly aligned see that ....

................. one of the two solder the cable to the motor brush stands over and already limaremos later.
When closing the car and rear skirts versions without the set is very bare and more to see the entire rear axle behind the reproduction of the gear shift and exhaust .....

........... It gets me a "fudge" to "cover" the area by cutting a piece of x-ray black to fit the hole of the "box" chassis .....

................ stick it to the back of "change" with glue transparent ..............


................. to cover and obscure the rear that both this model without skirts ugly ........


........... and stays that way ........


When closing the car with the three screws notice that is tilted to the right and search for the cause is due to soldering the wires to the motor protruding excessively.

With a little lime we have perfect ......


................. and we can mount the body ........


and sure that it is all seen from behind tight ...........

............. and lateralmete is much more authentic and realistic ......... although moth reproduction closure have oversized tires.

After the workshop session spent rolling on the track to see the improvements of this simple preparation.

We must roll to remove the first layer of rubber, but has the touch of silicone, a few laps so we stop to hit one of the rear wheels to be dropping, a bit of cyan on the shaft and press the rim waiting a few minutes to make it on your site.

Comment
the wheels and axles, but not calibrated in these decorated versions are fairly well aligned, only neumátcos have some slack in its abrasion factors and is required to settle well.


The car is not a machine to devour km track speed but does not go out and not wanting ....... to a rise in costs can be your competitive landscape, as tires lose some grip is necessary to loosen the screws to tilt the body freely (no need to sand anything or screw anything any) the tilt is perfect.

After testing and testing we came to the conclusion that the best way is on our home track is removed the two side screws and let the front screw tight, get a suspension effect very easy to note the times and take comfort in this magnificent reproduction of ..........

Substituting the axles and wheels for material calibrated with a superior engine performance is a candidate to "war" in the category of costs going up.
The lightness of the whole and the quality of its design is ideal for this specialty.
We will consider for next season. Salut Jordi
.

0 comments:

Post a Comment