Scuderia AAM Slot going to participate in a championship very interesting from the standpoint of configuration and regulation can see this link Le Mans Challenge . It is our desire to present our 4 "frames" and his basic training for:
1 º / Pass our best and ........
2 º / Getting to the final classification sporting what we as a team.
We've enrolled in the "queen" of Le Mans Prototype (LMP 1) as the most representative of the concept and idea Le Mans since GT are countless competitions Are European GT GT 2 or 3 that translated Slot 1 / 32 the difference between a GT 2 and GT 3 is little more than nothing for the plastic characteristics of the toy in question.
The issue of equality between manufacturers is reflected in the successful regulation Le Mans Challenge in the category GT the laster with 4 gr. vehicles lexan tray and 8 g . tray and glass with lexan although the ideal, in our opinion, is that the minimum weight body weight to remain in a balanced and consensus among all possible such as about 25 or 26 gr . would be more correct and ballast at the base of the tray puppet pilot figure represents the weight to these 26 gr. on all vehicles with a lower body to the 25 or 26 gr . This one
of NSR Mosler would equated with a Ninco Mosler of and Ford GT Ninco of dynamic conditions would equal a Lamborghini Diablo the same manufacturer, very heavy plastic tray, of course. But in short time to time! and the practical test and the passing of the championship will decide the best option for a fair regulation.
The use of different engines in each category is not very relevant since the JP than 21,000 Ref. MM18120 has better braking and allows greater development in the transmission that Hobby Slot -3 HRS Ref. ACR 022 of 23,000 and finally the importance of using appropriate transmissions in each category and emphasizes circuit and even closer possibilities victory.
......................................... - "Chickens coming by leaving" - ...............................
The use of the rear tires in each category is of a different manufacturer and may be more interesting in this " Le Mans Challenge " GT The shoes are by Ninco Slick 19x10 Ref. 890506 and category will be LMP Sloting Plus S2 19x8 Ref. SLPM -S2.
But as in the first year of this championship semester and is in effect admitting possible changes to regulate the equality of all the cars ho olog m in the rules that we cling to that time always gives reason to who has it and we let experience and the way we light up the best regulation possible.
lexan tray in LMP is testimony by the size of it and, therefore , the minimum weight for you, although the possibility of locating the motor in position at an angle toward the balance declines NSR Mosler of , are not allowed in the GT category their virtues dynamic but no magnetic field in the other, mostly 4-lane circuit, the issue is not so clear for what location engine balance tip the balance.
started, if you think well, with Radical SR 9, Scaleauto :
was ruled at first because I could not tilt the body by touching the "ring" engine mount original with the body and not rely on tape to replace the ring of the engine or motor stuck on the original bench Scaleauto decided to change the original engine mounting one of Slot it more reliably that contrasted maintaining fixation by screws .............
The cable routing is very important at all times and basic training.
front axle ......... lightness in the front is very important ..............
......... rim 16 m / m. Derlin PKS bucket with lid of Slot to win it in aesthetics.
That dynamic must never be unsightly ; rule that some forgotten in favor of performance final ............. but a beautiful car can also be fast.
rear rim 16.5 m / m. Merkur of Sloting Plus (very slight)
crown Scaleauto consists of two parts: a centering the brass and aluminum crown itself, so you can use any gear diameter, on the other hand we have to adjust centering and crown the gear is right and at the same time does not slow down by excessive friction. A crown aluminum, 27 teeth will do the same functions and will be easier to put in place in case of a possible replacement in the race.
For good sanding should tilt the "towers" anchoring body and chassis base as the two "turrets " fit within the frame supports without any slack preventing tilting of the body (regulations permitting)
The car, to be totally dismissed, has transformed into a devourer of lines and curves; only in the absence of a test in a broader circuit of Club for their "new" behavior promises, in the test track of my garage is going well being the " record -car" in lane No. 1 ( cheeses interior )
The other model prepared with in-line engine is the Audi R8 Avant Slot .
Its
View cable routing and the "blue pasta office" to secure its position.
View on the next image of the front axle regulation ..........
rear wheel for lightness Merkur of 16.5 m / m Sloting Plus.
Slightly bend the two plates alike and accentuating the curvature at one end that will be in contact with the bench / engine mount and rear as we see in the picture below.
We set the plates carefully without forcing them to pass through all the cracks of the "way" over leaving the back curvature coinciding with the top of the bed, 1m / m. less to work freely is not easy but once class is controlled.
Once you have set ...........
.................... 1 º / sure (do not overtighten) the plates with a grub screw in the center of the chassis (see Allen screw hole closest to the screw securing the drive to exhibiting urn) and 2
insert a second allen yes it is going to sevir to regulate the pressure of the plate (suspension) at our discretion and circuit driving. Tighter suspension harder and vice versa as we see in the picture below.
Avant The downside is that design can not regulate the suspension without removing the body.
The dynamic behavior is very even the Radical SR9 of bearings Scaleauto but makes you less brake and marccha wins overall smoothness, traction thanks to the suspension is great and the step for excellent outward curve and much higher than other vehicles are prepared in the intermediate track.
...... is the car that best suits the outset as the conditions are track, easy to carry, forgiving almost everything and everyone is more balanced.
now turn to Sloting Reynard Plus motor angle.
The cable routing is very important in preparing all ...........
We have done as follows. Remove the asparagus bottom
..................
................ and leave a gap above the axis of 2 m / m. (See picture below)
lose the possibility of external regulation, but we gain in reliability and security ........
................ we must regulate itself to the top brass screw shorter for the body does not touch the tops of pier and have free swing.
steps chassis screw are tight and we must ensure the proper tilt of the body. To do this we have several ways:
1 º / replacing the original screws and other less thick. 2 º spasms
a thicker drill the holes in the chassis.
3 º / We modify the original screws limándolos as follows .........
............... keep the original plastic cap to ensure a perfect meshing with the pinion and crown hogura not be necessary for self-braking (picture below)
We tested different types of tires, lighter Merkur heavier Sloit it and the best result has given us is the original model. This car needs very low weight back and to counter the flight height and the rear wing as the ballast is not permitted by rules we have to mount the most significant component.
test track in our garage is excellent with a smooth and acceptable running sound ...............
now turn to the NSR Mosler engine at an angle.
Although the versatility of this manufacturer allows any type of configuration.
The guide must be adapted to all types of rail will be Ninco or SCX.
And we should be that simple.
spring rear suspension through regulated NSR to our liking.
a pity! Dynamic test
:
The red longitudinal split bench while trying to mount the engine and returned to the supplier.
From these lines and circuit experience "home" minimum course, we support both inline engine and in particular the Avant Slot model much easier to drive on unknown tracks by our team and leaving the Radical Scaleauto as an option if the first fails.
The Reynard Sloting Plus account costs more than "fuck optimum dynamic temperature" and the first round after each round you penalized.
The Mosler is a good option but we would have liked to try the online option as we believe that in the category of LMP regulations should limit the location of the engine on a grid line to see more colorful and realistic models of PML fashion than is now possible to see many NSR Mosler GT in a category that is not theirs. (the subject of breaking the benches of this manufacturer claims the sky)
hope you have been a guide and "shortcut" in whole range of possibilities for the preparation of all these models.
There are many other and are approved by the rules but we have opted for the 4 "Riders." All competitive and easy to drive.
shame that career length is only 4 hours! Salut Jordi
.
0 comments:
Post a Comment